Antenna polarisers

High performance waveguide polarizers for transmission or reception

Polarisers

Celestia TTI can supply standard polarisers in Ku band, as well as develop custom solutions as per customer´s requirements at different frequency bands

Polar antennas rf passive products
TYPE DESCRIPTION FREQUENCY DATASHEET
Polariser Transmission Ku Request
Polariser Reception Ku Request

Technical Specifications by Family

Celestia TTI’s Ku band polarisers are precision-machined waveguide components designed for integration into satellite antenna feed chains. Full datasheets are available on request. Key performance parameters include:

Parameter Specification
Frequency Band Ku band (standard); custom bands available
Function Linear-to-circular polarisation conversion
Polarisation Output LHCP or RHCP (specified at time of order)
Axial Ratio ≤1.0 dB (typical target for high-performance designs)
VSWR Low — waveguide technology minimises reflections
Insertion Loss Low — passive waveguide component
Waveguide Interfaces Standard Ku band rectangular and circular waveguide flanges
Configuration Transmission (Tx path) or Reception (Rx path)
Custom Options Frequency band, polarisation sense, waveguide standard, form factor

Contact Celestia TTI for full datasheets and custom configuration specifications.

Linear-to-Circular Polarisation Conversion for Satellite Feed Chains

A waveguide polariser converts linearly polarised signals into circularly polarised signals — or vice versa — by introducing a controlled 90° phase shift between the two orthogonal field components of the electromagnetic wave. In satellite antenna feed systems requiring circular polarisation, the polariser sits between the corrugated feed horn and the Orthomode Transducer (OMT), completing the passive feed chain that separates or combines the Left-Hand Circular (LHCP) and Right-Hand Circular (RHCP) polarisation paths.

Circular polarisation is widely used at C band and is ideal in tropical areas where Faraday rotation in the ionosphere causes changes to linear polarisation orientation — a phenomenon that is negligible at higher frequencies like Ku band but significant at lower frequencies. Middle East Satellite Internet service providers At Ku band, circular polarisation is used on a number of satellite systems to enable frequency reuse — where the same frequency band carries simultaneous LHCP and RHCP channels — and to simplify feed alignment in mobile terminal applications.

Celestia TTI supplies standard waveguide polarisers in Ku band for both transmission and reception, and develops custom solutions at different frequency bands to customer specifications.

Key Advantages

Separate Tx and Rx Configurations

Celestia TTI offers dedicated polariser designs for the transmission and reception paths, optimised for the different power levels, frequency sub-bands, and insertion loss budgets of each path. This ensures the polariser contributes minimally to noise in the receive chain and handles the power requirements of the transmit chain without performance degradation.

Precision Waveguide Manufacturing

Polariser performance — particularly axial ratio and cross-polarisation isolation — is directly dependent on dimensional accuracy of the waveguide structures. An axial ratio up to 1 dB is considered to give a very good circularly polarised wave and is generally a difficult specification to meet, with values around 2 dB being more realistic in practice. Milsatmagazine Celestia TTI's precision CNC machining achieves the tight tolerances required for high-performance circular polarisation conversion.

Feed Chain Integration

Celestia TTI designs polarisers as part of complete feed chain solutions — mechanically compatible with the company's corrugated feed horns and OMTs. This eliminates interface mismatches between passive components and ensures the assembled feed chain performs as a system rather than as individual parts.

Custom Frequency and Polarisation Sense

Beyond standard Ku band, Celestia TTI develops polarisers for other satellite frequency bands and specific polarisation sense requirements (LHCP or RHCP output). Custom solutions are engineered to the waveguide interfaces, frequency sub-band, and axial ratio requirements of each application.

Passive, Maintenance-Free Operation

As entirely passive waveguide components with no moving parts or active electronics, polarisers require no maintenance and add no noise to the receive chain. Their reliability profile is determined purely by mechanical integrity — making them the lowest-risk component in the feed chain assembly.

Celestia TTI: Complete Passive Feed Chain Engineering

A polariser specified, manufactured, and tested in isolation from the feed horn and OMT it connects to risks mismatched waveguide interfaces, incorrect polarisation sense, or system-level performance that differs from component-level predictions. Celestia TTI’s position as a manufacturer of the complete passive feed chain — feed horns, polarisers, and OMTs — allows co-design and co-testing that individual component suppliers cannot offer.

Integrated Design

Polarisers are designed to interface directly with Celestia TTI’s corrugated horn families and OMT portfolio, with consistent waveguide standards, flange dimensions, and electrical interfaces across the feed chain assembly.

Custom Engineering

For non-standard frequency bands, unusual polarisation configurations, or specific physical form factor requirements, Celestia TTI’s RF engineering team develops custom polariser designs validated by electromagnetic simulation and measured performance data.

Quality Assurance

ISO 9001:2015 certified manufacturing ensures dimensional consistency and documented traceability for every component in the feed chain.

Applications

Application 1: Circular Polarisation Satellite Earth Stations

Earth stations communicating with satellites that use circular polarisation — including several C band networks and specific Ku band systems — require a polariser in the feed chain to convert between the linear polarisation of the OMT ports and the circular polarisation required at the antenna aperture. Celestia TTI's Ku band polarisers integrate into standard earth station feed assemblies alongside the feed horn and OMT.

Application 2: Frequency Reuse Antenna Systems

Because LHCP and RHCP signals are orthogonal to each other, satellite systems use alternating circular polarisations to separate adjacent transponders or to reuse the same frequency for uplink and downlink — effectively doubling the spectral efficiency of a given frequency allocation. Milsatmagazine Feed chains for antennas accessing these frequency-reuse satellite systems require high-isolation circular polarisers to maintain adequate separation between co-frequency LHCP and RHCP channels.

Application 3: SATCOM-on-the-Move (SOTM) Terminals

Circular polarisation simplifies satellite signal capture for mobile terminals, as the antenna need only be steered toward the satellite boresight without further adjustment of the transverse feed angle — avoiding the polarisation alignment requirement of linear polarisation systems. Milsatmagazine Mobile SATCOM terminals at Ku band and Ka band benefit from circular polarisation feed chains for this operational simplicity.

Application 4: Custom Feed Chain Assemblies

For antenna projects requiring complete passive feed chain solutions, Celestia TTI supplies the polariser as part of an integrated assembly including the corrugated feed horn and OMT — all designed and tested together as a system. This turnkey feed chain approach is relevant for ground station builds, antenna test range feeds, and scientific receiver installations.

Frequently Asked Questions

What does a waveguide polariser do?

A waveguide polariser converts a linearly polarised signal into a circularly polarised signal by introducing a 90° phase shift between the two orthogonal electric field components in the waveguide. The output is either Left-Hand Circular Polarisation (LHCP) or Right-Hand Circular Polarisation (RHCP) depending on the orientation of the polariser. In an antenna feed chain, the polariser is placed between the feed horn and the OMT, enabling the overall system to transmit or receive circularly polarised signals using components that otherwise handle linear polarisation.

A polariser converts between linear and circular polarisation — it changes the polarisation state of the signal. An OMT separates or combines two orthogonally polarised signals into separate waveguide ports — it manages the routing of polarisation channels without changing their polarisation state. In feed chains requiring circular polarisation, both components are typically used together: the polariser performs the linear-to-circular conversion, and the OMT separates the two resulting circular polarisation channels into the transmit and receive paths.

The transmit and receive paths in a satellite feed chain operate at different frequency sub-bands, carry very different power levels, and have different performance priorities. The Tx polariser must handle the full output power of the BUC or SSPA, while the Rx polariser must minimise insertion loss to protect receive chain noise temperature. Designing separate components for each path allows optimisation of dimensions, waveguide interface, and insertion loss independently for each direction.

Standard products are available in Ku band for both transmission and reception. Custom solutions are available at other frequency bands — contact Celestia TTI with your frequency sub-band, polarisation sense, waveguide interface, and axial ratio requirements.

The polarisation sense determines the orientation of the phase-shifting element within the polariser waveguide. LHCP and RHCP polarisers differ in the direction of the 90° phase shift they introduce. The required polarisation sense must be specified at the time of order, as it determines the mechanical configuration of the component. In some designs, the polarisation sense can be changed by rotating the polariser 90° relative to the OMT — but this should be confirmed with the engineering team for each specific product.

Did you want to know more about our Passive RF components?

ISO 9001:2015Certified Quality
25+ YearsRF Heritage
100+ EngineersRF Specialists
ESA QualifiedSpace-Grade
5 ContinentsGlobal Clients
Content last reviewed: April 22, 2026 by Celestia TTI Engineering Team